SCM Olimpic 500 HP

GENERAL FEATURES

Automatic single-sided edge bander for the application and gluing of edges with hot melt glue on straight panels, on the four panel sides and the finishing and rounding-off of the panel corners.

Main frame made of bended and welded steel plates. Highly stiff and vibration-free structure. Openings with shoots for the removal of chips to the floor that are not collected by the dust extraction.

Top steel presser complete with two rows of rubber coated wheels mounted on bearings. Cover for wheel protection. Automatic lifting of presser from machine control.

Panel infeed area consisting of a support table and lateral guide for a correct panel insertion.

Light-signaling device positioned on the machine infeed side indicating the correct distance of panel insertion and the operating status of the machine, by different colors.

Top working units fixed on the presser, while bottom working units fixed to the horizontal beam for a precise reference with respect to the panel.

All frequency motors are equipped with inverter.

Safety cabin on the entire length of the machine with polycarbonate windows for the unit viewing during machining.

2 doors provide access to the working units, one for the gluing area and one for the finishing area. Doors have independent management of each other.

Exhaust outlets for the operating units are positioned on the top side of the safety cabin.

Control panel in an ergonomic position at machine infeed for an easy use from the operator’s working position

Electrical cabinet positioned inside the main frame with doors that allow an easy access in case of any maintenance operations. The cabinet is in conformity with the current safety regulations.

Panel handling by means of feed track consisting of pads coated with high friction rubber and ¾ link industrial chain.

Sliding of pads on two guideways, one round and one flat, to ensure straightness of movement and resistance to side loads.

Manual pads lubrication.

Panel support rollers positioned parallel to the track on the entire length of the machine with telescopic opening system and sliding plastic wheels with steel pivot pins.

Weight	3500 lbs

Videos

Comparisons

Olimpic 500plus vs Olimpic 500 — Comparison Chart

Feature / Subsystem	olimpic 500plus — HP T-ER2	olimpic 500 — HP T-ER2
Document / model label	R0.11.66 olimpic 500plus — composition “HP T-ER2”	R0.12.59 olimpic 500 — composition “HP T-ER2”
Machine length	4950 mm	4950 mm (40 interaxis)
Feed / working speed	Variable 12–18 m/min (inverter-driven)	12 m/min (specified)
Panel thickness range	8 – 60 mm	8 – 60 mm
Strip (solid) edge thickness	0.3 – 8 mm (optionally up to 12 mm)	0.3 – 6 mm
Coiled (rolled) edge	0.3 – 3 mm; max section 135 mm²; coil-holder Ø 780 mm	0.3 – 3 mm; max section 135 mm²; coil-holder Ø 780 mm
Edge exceeding	2 + 3 (5* with max 3 mm edge thickness)	2 + 3 (5* with max 3 mm edge thickness)
Minimum panel / 4-side dims	Min length 140 mm; 4-side min 140 × 140 mm; lengthwise min 240 × 60 mm	Min length 140 mm; 4-side min 140 × 140 mm; lengthwise min 240 × 60 mm
Panel gap / distance	Panel gap 600 mm	600 mm (without rounding); 650 mm (with rounding)
Panel roller support / table height	Support opening 500 mm; table height 900 mm	Support opening 500 mm; table height 900 mm
Panel handling / feed chain	1-1/4″ link industrial chain + high-friction pads — built for heavy/continuous production; speed 12–18 m/min	3/4″ link industrial chain + high-friction pads — speed 12 m/min
Top presser	Electronic positioning according to panel thickness	Electronic top presser positioning (automatic)
Gluing unit / power	VC-S4.1 with SGP pot & iGlue; heating <10 min; installed power 2.23 kW; glue cap 0.5/1.5 kg	VC-VM with SGP-E; heating <12 min; installed power 1.61 kW; glue cap 0.5/1.5 kg
End cutting unit / motor	K/SEL — motor 0.35 kW; cutters 12,000 rpm	K-2/I — motor 0.2 kW; cutters 12,000 rpm
Trimming / chamfering (R-HP)	Motor 0.65 kW; solid wood trimming up to 8 mm; 4 controlled axes	Motor 0.65 kW; solid wood trimming up to 6 mm; 4 controlled axes
Rounding unit	Round 2-A Multiedge 1R — motor 0.35 kW; cutters 12,000 rpm; 0.3–3 mm edge	Same — motor 0.35 kW; cutters 12,000 rpm; 0.3–3 mm edge
Edge / glue scraping & brushing	RAS-HP Multiedge 2R, RC-N glue scraping, SP-V brushing (0.13 kW motors)	RAS-HP Multiedge 2R, RC-N glue scraping, SP-V brushing (0.13 kW motors)
Control console / HMI	eye-M EVO — 24″ FullHD touch, Intel i3, 8 GB RAM, SSD 256 GB, Windows 10 IoT; Maestro Connect 1-yr subscription included (gateway)	eye-S — 15″ 1366×768 touch, 2 GB RAM; Qs Monitor (Linux); Maestro Connect basic cabling only (gateway/subscription not included)
Electrical / safety / packaging	UL/CSA available; 220/230 V 50/60 Hz; pallet & packaging per quote	UL/CSA available; 220/230 V 50/60 Hz; pallet & packaging per quote
Quoted total price (doc)	USD $142,750 — Gross price $133,250 + Installation & testing $9,500 (quoted configuration)	Price not populated in file (table shows 00,000) — see original quotation

Quick summary — main differences

Throughput: 500plus up to 18 m/min vs 500 at 12 m/min.
Edge capability: 500plus supports thicker strip edges (8 mm / option 12 mm) and solid wood trimming to 8 mm (vs 6 mm).
Robustness: 500plus has a heavier 1-1/4″ feed chain and stronger cutter motor — better for heavy/continuous work.
Gluing & HMI: 500plus includes a more powerful glue pot and a 24″ eye-M EVO console with Maestro Connect subscription included.

Sources: SCM quotations — olimpic 500plus (US-004042) and olimpic 500 (US-003782).
Reference: :contentReference[oaicite:0]{index=0} :contentReference[oaicite:1]{index=1}